Services

Services Offered

Tensile Testing:

11.25 KIPS (50 KN) ADMET MODEL 2613 (EP2 SERVO CONTROL)

CICK HERE TO SEE IMAGE

Specifications:

Tension Testing opening/Compression Testing Opening: 52”

Distances between columns/screws: 16.8”

Table Size: 16.8" * 5"

Electro-Mechanical Unispace Tension and Compression (S/N: 351210A) Testing Stroke: 46”

Testing Speed: .00002-20 IPM

Crosshead adjusting speed: 20 IPM Weight: 375 lbs

10K (50 kN) Interface Load Cell S/N: 351210A

Monotonic/Dynamic Wind Uplift Testing:

CLICK HERE TO SEE IMAGE

Specifications:

Pressure suction as high as 14.4 kPa (300 psf) over the roof assembly is produced by a 74.4-kW (100 hp) fan with a flow rate of 5000 L/s (10594.4 ft3 /min)

  • Top Chamber, Bottom Frame with 12 by 24 ft in size that structurally strong with four lifting mechanisms for the top chamber to a maximum height of 10 ft from the ground. (Items #1 and #2)

  • Fan system (Blower and Inverter) that can simulate a minimum of 300 psf suction (Item #3)

  • Gust simulator (Flap and Servo Motor) that can reproduce the CSA A123.21 wind gusts (Item #4)

  • Sensors and Data acquisition system necessary to measure the system performance as per CSA A123.21 (Item #5)

  • Control system that runs the CSA A123.21 test protocol via executable software

Monotonic/Dynamic Load Frame Testing:

 CLICK HERE TO SEE IMAGE

Specifications:

Lateral Dynamic Hydraulic Linear Actuator:
  • (22kip/100kN) [Fatigue Rated]
  • 2.75 Inch (69.85 mm) heat treated alloy piston rod
  • Force ± 22,260lb (99kN) @ 3000 psid (210 bar)
  • 7.42 in2 equal area (47.87 cm2)
  • Manifold: Integral dual servo valve manifold with Moog 761 series valve pattern.
  • Load Cell: 25 kips (125 kN) nominal fatigue rating, 300% overload capacity.
  • Servo Valve: Moog G761-3005 valve rated at 16.5 GPM (62.4 IPM) @1000 psid (70 bar)
  • Shore Western Model: 912D-7.42-10-4-2348
Vertical Dynamic Hydraulic Linear Actuator (110 kip/500kN):
  • Force ± 115,000lb (513 kN) @ 3000 psid (210 bar)
  • 38.48 (in2) equal area (248cm2)
  • Stroke: 10 in (254mm) ± 5 in
  • Mounting: Swivel Base rated at ± 110-kip (500kN) dynamic, + 150 kip (670kN) static compression, +30-90° swivel ± 6° tilt
  • Rod End: Swivel; Rod End rated at 110-kip (500 kN) dynamic, +150 kip (670 kN) static compression, +30-90° swivel ± 6° tilt
  • Manifold: Integral dual servo valve manifold with Moog 761 series valve pattern.
  • Load Cell: 110 kip (500kN) nominal calibrated rating. 300% overload capacity.
  • Servo Valve: Moog G761-3005 valve rated at 16.5 GPM (62.4 IPM) @1000 psid (70 bar)
  • Shore Western Model: 914D-38.48-10-4-2348